Hybrid Particleboard Made of Corn Husk (Zea Mays L.) and Sembilang Bamboo (Dendrocalamus Giganteus Munro): Effect of Adhesive Type and Particle Composition

Kurnia Wiji Prasetiyo, Dede Hermawan, Yusuf Sudo Hadi, Subyakto Subyakto, Muhammad Firdaus, Firda Aulya Syamani, Lilik Astari

Abstract

Particleboard is a panel product made of wood particles or other lignocellulosic materials added with adhesive then pressed. The development of particleboard manufactured using non wood biomass has become important due to the decreased of wood as main raw material for the particleboard industry. Corn husk (Zea mays L.) and Sembilang bamboo (Dendrocalamus giganteus Munro) are lignocellulosic biomass that has  potential as  renewable materials for hybrid particleboard. The purposes of this study were to determine the suitability, the effect of adhesive type, and particle composition on physical and mechanical properties of hybrid particleboard made of corn husk and Sembilang bamboo particles. The adhesive types used were urea formaldehyde (UF) and phenol formaldehyde (PF) with 10 wt% adhesive content and the composition of corn husk : Sembilang bamboo was  set at 100 : 0, 75 : 25, 50 : 50, 25 : 75, 0 : 100 (% w/w). The target density of hybrid particleboard was set at 0.80 g/cm3. The boards were manufactured at 130 °C for UF and 150 °C for PF press temperature, 10 minutes and 2.5 MPa for the pressure of the hot press. The results showed that hybrid particleboard properties improved with increasing the amount of Sembilang bamboo particles in the board. Hybrid particleboard properties affected in ascending order were modulus of rupture (MOR), modulus of elasticity (MOE), internal bond (IB) and screw holding power (SHP). Generally, hybrid particleboard bonded PF adhesive has better properties than bonded UF adhesive. Results indicated that the addition of Sembilang bamboo particles in the mixture resulted in better properties of hybrid particleboard.

Keywords

Adhesive type; Corn husk; Hybrid particleboard; Particle composition; Sembilang bamboo

Full Text:

PDF

References

Astari, L., Prasetiyo K. W., Suryanegara, L. 2018. Properties of Particleboard Made from Wood Waste with Various Size. IOP Conference Series: Earth and Environmental Science. 166: 012004.

Astari, L., Syamani, F. A., Prasetiyo, K. W. 2019. Physical, mechanical and acoustical properties of particleboard made from corn stalk (Zea mays L). Jurnal Riset Industri Hasil Hutan. 11 (1): 41-52.

Baskaran, M., Hashima, R., Sudesh, K., Sulaimana, O., Hiziroglu, S., Arai, T., Kosugi, A. 2013. Influence of steam treatment on the properties of particleboard madefrom oil palm trunk with addition of polyhydroxyalkanoates. Journal Industrial Crops and Products. 51: 334– 341.

Bektha, P., Noshcenko, G., Reh, R., Kristak, L., Sedliacik, J., Antov, P., Mirski, R., Savov, V. 2021. Properties of Eco-friendly Particleboard Bonded with Lignosulfonate-Urea-Formaldehyde Adhesives and pMDI as a Crosslinker. Materials 14: p.4875.

Central Bureau of Statistics (BPS). 2018. Indonesia Statistics of 2018. Jakarta

Cheng, X., He, X., Xie, J., Quan, P., Xu, K., Li, X., Cai, Z. 2016. Effect of the Particle Geometry and Adhesive Mass Percentage on the Physical and Mechanical Properties of Particleboard made from Peanut Hull. BioResources. 11(3): 7271-7281.

Dirgantara, M. 2013. Karakterisasi Mekanik Biokomposit Klobot Jagung Sebagai Bahan Dasar Plastik Biodegradable. Skripsi: Jurusan Fisika Fakultas Matematika dan Ilmu Pengetahuan Alam IPB.

Food and Agriculture Organization. 2018. Forest product statistic: 2018 global forest products: production and trade. Forest Economic, Policy and Product Division FAO Forest Department, Rome.

Guler, C., Sahin, H. I., Yeniay, S. 2016. The potential for using corn stalks as a raw material for production particleboard with industrial wood chips. Journal of Wood Research. 61(2): 299-306.

Hashim, R., Said, N., Lamaming, J., Baskaran, M., Sulaiman, O., Sato, M., Hiziroglu, S., Sugimoto, T. 2011. Influence of press temperature on the properties of binderless particleboard made from oil palm trunk. Materials and Design. 32(5): 2520–2525.

Iswanto, A. H., Anjarani, H. D. 2018. The Properties of Sandwich Particleboard (SPB) Made From Bamboo Belangke and Corn Stalk Bagasse Bonded With Isocyanat in Various Levels. IOP Conference Series: Earth and Environment Science. 209: 012031.

Japanese Industrial Standard (JIS). 2003. JIS A 5908:2003 Particleboard. Japanese Standard Association. Tokyo, Japan.

Juliana, A. H., Paridah, M. T., Rahim, S., Azowa, I. N., Anwar, U. M. K. 2012. Properties of particleboard made from kenaf (Hibiscus cannabinus L.) as function of particle geometry. Journal Materials and Design. 34: 406-411.

Kariuki, S. W., Wachira, J., Kawira, M., Murithi, G. 2019. Formaldehyde Use and Alternative Biobased Binders for Particleboard Formulation: A Review. Journal of Chemstry. Special issue: Conversion of Lignocellulosic Biomass and Derivatives into Value-Added Heteroatom-Containing Compounds. Volume 2019. Article ID 5256897.

Kasim, J., Ahmad, A. J. H., Harun, J., Ashari, Z., Mohmod, L., Yusof, M. N. M. 2001. Properties of particleboard manufactured from commonly utilized Malaysian bamboo (Gigantochloa scortechinii). Pertanika Journal Tropical Agricultural Science. 24(2): 151-157.

Kelly, M. W. 1977. Critical literature review of relationships between processing parameters and physical properties of particleboard. (In: General Technical Report FPL-10 USDA Forest Service Forest Product Laboratory Madison).

Kusumah, S. S., Umemura, K., Yoshioka, K., Miyafuji, H., Kanayama, K. 2016. Utilization of sweet sorghum bagasse and citric acid for manufacturing of particleboard I : Effects of pre-drying treatment and citric acid content on the board properties. Journal Industrial Crops and Products. 84: 34–42.

Maloney, T. M. 1993. Modern Particleboard and Dry Process Fiberboard Manufacturing (San Francisco Miller Freeman Publication Inc. California).

Mccutcheon, J., Samples, D. 2002. Grazing Corn Residues. Extension Fact Sheet Ohio State University Extension. US. ANR10-02.

Ministry of Agriculture. 2020. Inilah 10 Provinsi Produsen Jagung Terbesar Indonesia. www.pertanian.go.id/home/?show=news&act=view&id=4639. Accessed on 29 November 2021.

Melo, R. R., Stangerlin, D. M., Santana, R. R. C., Pedrosa, T. D. 2014. Physical and Mechanical Properties of Particleboard Manufactured from Wood, Bamboo and Rice Husk. Materials Research. 17(3): 682-686.

Ndazi, B., Tesha, J. V., Bisanda, E. T. N. 2006. Some opportunities and challenges of producing bio-composites from non-wood residues. Journal of Materials Science. 41: 6984-6990. DOI: 10.1007/s10853-006-0220-7.

Nurhazwani, O., Jawaid, M., Paridah, M. T., Juliana, A. H., Hamid, S. A. 2016. Hybrid Particleboard Made from Bamboo (Dendrocalamus asper) Veneer Waste and Rubberwood (Hevea brasilienses). BioResources. 11 (1): 306-323.

Pardosi, F., Latief, T., Pratama, F. 2012. Karakteristik papan partikel berbahan sekam padi dengan penambahan paraffin. Jurnal Teknik Pertanian Sriwijaya. 1(1): 28-38.

Prasetiyo, K. W., Octaviana, L., Astari, L., Syamani, F. A., Subyakto, Achmadi, S. S. 2018. Physical-mechanical properties and bonding mechanism of corn stalks particleboard with citric acid adhesive. Jurnal Ilmu dan Teknologi Kayu Tropis. 16(2): 134-135.

Prasetiyo, K. W., Astari, L., Syamani, F. A., and Subyakto. 2019. Physical and mechanical properties of urea formaldehyde and phenol formaldehyde-bonded particleboards made from corn stalk. IOP Conference Series: Earth and Environmental Science. 374: 011002.

Sekaluvu, L., Tumutegyereize, P., and Kiggundu, N. 2014. Investigation of factors affecting the production and properties of maize cob-particleboards. Waste and Biomass Valorization. 5: 27–32.

Shmulsky, R., Jones, P. D. 2011. Forest Products and Wood Science: An Introduction, 6th Edition. JohnWiley & Sons: Chichester, West Sussex, UK.

Theng, D., Arbat, G., Aguilar, M.D., Vilaseca, F., Ngo, B., Mutje, P. 2015. All-lignocellulosic fiberboard from corn biomass and cellulose nanofibers. Journal Industrial Crops and Products. 76: 166-173.

Valarmathi, T., Palanikumar, K., Latha, B. 2013. Measurement and analysis of thrust force in drilling of particleboard (PB) composite panels. Measurement. 463: 1220–1230.

Veigel, S., Rathke, J., Weigl, M., Gindl-Altmutter, W. 2012. Particleboard and oriented strand board prepared with nanocellulose-reinforced adhesive. Journal of Nanomaterials, Vol. 2012, Article ID 158503: 1-8.

Widjaja, E. A. 2001. Identikit Jenis-jenis Bambu di Jawa. Seri Panduan Lapangan. LIPI: Bogor, Indonesia. (in Indonesian).

Zhang, L., Hu, Y. 2014. Novel lignocellulosic hybrid particleboard composites made from rice straws and coir fibers. Materials and Design. 55: 19–26.

DOI: https://doi.org/10.15294/jbat.v10i2.31600

Refbacks

  • There are currently no refbacks.


Bookmark and Share