The effect of cutting speed on the roughness level of low carbon steel cutting results using the trulaser 3030 machine
DOI:
https://doi.org/10.15294/jmel.v13.i1.5503Keywords:
Cutting Speed, Laser, Low Carbon Steel, RoughnessAbstract
This research aims to determine the effect of variations in cutting speed on the roughness value of low carbon steel cutting results using CNC Laser Cutting TruLaser3030. This research uses experimental methods and descriptive statistical data analysis techniques and diagrams to present data on the measurement results of research specimens using cutting speeds of 2520 mm/minute, 2205 mm/minute, and 1890 mm/minute. Roughness testing was carried out using Surface Roughness Mitutoyo SJ-210. The results of the research produced data showing that the higher the cutting speed, the roughness value increases and the lower the cutting speed, the roughness value will decrease. And if the cutting speed is too high then the material cannot be cut. The lowest roughness value, namely 8.46µm, was at a cutting speed variation of 1980 mm/minute. The highest roughness value, namely 23.63µm, occurs at a cutting speed variation of 2520 mm/minute.
References
Amaral, I., Silva, F. J. G., Pinto, G. F. L., Campilho, R. D. S. G., & Gouveia, R. M. (2019). Improving the cut surface quality by optimizing parameters in the fibre laser cutting process. Procedia Manufacturing, 38(1), 1111-1120. https://doi.org/10.1016/j.promfg.2020.01.199
Badoniya, P. (2018). CO₂ laser cutting of different materials—A review. Int. Res. J. Eng.Technol,i5(6). https://www.researchgate.net/publication/330350894
Genna S, Menna E, Rubino G, & Tagliaferri V. (2020). Experimental investigation of industrial laser cutting: The effect of the material selection and the process parameters on the kerf quality. Applied Sciences,I10(4956). https://doi.org/10.3390/app10144956
Hidayat, M. A., Farid, A., & Suwandono, P. (2021). Analisa parameter pada pemotongan plate menggunakan CNC fiber laser cutting terhadap kekasaran permukaan. Jurnal Program Studi TeknikMesin, 10(2). http://ojs.ummetro.ac.id/index.php/turbo
Ningrum, H. W. (2021). Pengaruh parameter pemotongan mesin laser cutting terhadap kekasaran permukaan dan keakuratan geometri stainless steel 304. Doctoral Dissertation, Universitas GadjahMada. https://etd.repository.ugm.ac.id/penelitian/detail/200913
Rahmawati, A. R., Anis, S., & Rusiyanto, R. (2019). Pengaruh kecepatan pemotongan dan ketebalan bahan terhadap kekerasan dan kekasaran permukaan Baja AISI 1045 menggunakan CNC Plasma Arc Cutting. Jurnal Dinamika Vokasional Teknik Mesin,4(2).
http://dx.doi.org/10.21831/dinamika.v4i2.27390
Rizal, M., Usman, H., & Adel, R. Y. (2022). Fiber laser cutting of aisi-304 stainless steel: an experimental study of the influence of process parameters on kerf width and cutting edge quality. Jurnal Teknik Mesin, 10(2). https://doi.org/10.24815/jtm.v10i2.30873
Roziqin, A., & Aryadi, W. (2021). Finite element analysis of village car pickup ladder frame chassis-a case study. IOP Conference Series: Earth and EnvironmentaljScience,i700(1).
https://doi.org/10.1088/1755-1315/700/1/012008
Isyrouddin, F. A. I. A., & Sumbodo, W. (2020). Pengaruh Variasi Sudut Potong Mayor Terhadap Kekasaran Permukaan Hasil Proses Pembubutan Muka Aluminium Silicon (Si) Daur Ulang. JMEL : Journal of Mechanical Engineering Learning, 12(1). https://journal.unnes.ac.id/sju/jmel/article/view/14505
Satyawardhana, N., Lubis, M. S. Y., & Rosehan, R. (2022). Optimasi parameter proses laser cutting terhadap kekasaran permukaan material acrylictype clear dengan menggunakan metode taguchi. Seminar Nasional Teknik (SEMNASTEK)UISU, 5(1). https://jurnal.uisu.ac.id/index.php/semnastek/article/view/5623/4112
Downloads
Article ID
Published
Issue
Section
License
Copyright (c) 2024 Husni Amron, Ahmad Roziqin (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
